Steel-Wood Laboratory Bench with Epoxy Resin Worktop

What is the Steel-Wood Laboratory Bench with Epoxy Resin Worktop?

A steel-wood laboratory bench combines a powder-coated steel frame with melamine or laminated wood cabinets and an epoxy resin worktop. It gives good chemical resistance at moderate cost and is the usual choice for general chemistry and teaching laboratories.

Overview

This design uses a welded tubular steel frame for load bearing and moisture-resistant particleboard or plywood carcasses for cabinets, with solid epoxy resin worktops typically 20 mm thick. The steel frame isolates the cabinets from floor moisture, while the resin top tolerates strong acids, alkalis and most organic solvents. Drawers and doors run on steel hardware, and adjustable feet compensate for uneven floors. Reagent shelves, electrical sockets and gas taps can be fitted to a central service spine. The wood cabinets are lighter and easier to customize than all-steel units but are less suited to continuous wet or fire-critical environments. Typical modules are 600 mm wide and 750 mm deep.

How does it work?

A laboratory bench consists of a structural frame, a worktop and usually base cabinets or drawers. Frames are welded or bolted steel, powder-coated or stainless, sized for distributed loads of typically 200–500 kg per linear metre. Worktops are chosen for chemical and thermal exposure: epoxy resin, phenolic resin, solid-surface, ceramic or stainless steel. Reagent shelves, service spines and pop-up sockets carry electricity, gas, vacuum and water, while drop-in sinks and fume-hood interfaces complete the wet-lab workflow. Leveling feet compensate for floor unevenness, and cantilever or modular frames allow reconfiguration. Finish durability depends on powder-coat film thickness, edge sealing and the resistance of the worktop to acids, solvents and heat per standard surface tests.

What are the key features?

• Powder-coated steel frame rated to about 300 kg per linear metre
• 20 mm solid epoxy resin worktop with drip groove
• Melamine or laminated wood cabinets on steel frame
• Adjustable leveling feet for uneven floors
• Optional reagent shelf and service spine with sockets and taps
• Modular 600 mm widths for flexible layouts

What are the technical specifications?

A typical steel-wood laboratory bench with epoxy resin worktop configuration offers worktop material of Solid epoxy resin, 20 mm, frame material of Powder-coated steel tube, cabinet material of Melamine particleboard, 18 mm, standard depth of 750 mm, standard height of 850 mm and module width of 600 / 900 / 1200 mm. Values are indicative of the product class; the exact figures for each configuration are confirmed on the quotation and the calibration documents supplied with the instrument.

Which applications is it used for?

The Steel-Wood Laboratory Bench with Epoxy Resin Worktop is used in teaching chemistry laboratories, quality control laboratories, research support labs and material testing rooms. Across the wider Laboratory Benches class, laboratories also deploy it for chemistry teaching and research labs, pharmaceutical QC laboratories and biology and microbiology labs.

Which standards and certifications apply?

Relevant standards and methods include SEFA 8 (laboratory grade casework), EN 13150 (laboratory workbenches), GB 24820 (laboratory furniture, Chinese national standard), ANSI/BIFMA X5.5-style load testing (reference) and ISO 9001 quality management. Certification candidates for this model are ISO 9001 manufacturing, SEFA 8 test report and GREENGUARD-type low emission test; each is to be confirmed for the specific configuration before shipment, and certificates are supplied only where they have been issued.

Plan the room before ordering: floor flatness, door widths, ceiling height, service routes and fume hood positions determine which bench designs are feasible. Anchor tall benches per seismic or safety requirements and level all feet before installing worktops. Seal joints and penetrations with chemical-resistant silicone. Verify electrical safety to IEC 61010-1 room practice and keep services isolated from wet zones. Maintenance is simple: wipe spills promptly, avoid abrasive pads on resin, inspect hinges and drawer runners every six months, and re-seal edges if the coating is breached. Document material resistance charts for safety assessments.

How do I select the right Steel-Wood Laboratory Bench with Epoxy Resin Worktop?

Select this variant for general chemistry, teaching and QC rooms where chemical resistance is needed but fire or continuous-wet conditions are not extreme. Compared with all-steel benches it costs less, and compared with phenolic tops it resists stronger chemicals. In an RFQ, state worktop thickness, chemical list, module sizes, service spine requirements and cabinet configuration.

How does it compare with other Laboratory Benches variants?

Choose by the chemicals and heat the worktop will see first: epoxy resin handles strong acids and solvents, phenolic resin suits general chemistry and teaching, stainless steel suits biology and cleanroom use, and ceramic suits high-temperature work. Then set the load rating, because balances, centrifuges and ovens need rigid frames with vibration control. Decide whether the layout is fixed, height-adjustable or mobile, and whether service spines, sinks or reagent shelves are required. Check total length, depth (typically 750 mm), height (typically 850–900 mm) and accessibility requirements. Finally, verify finish resistance data, edge sealing and manufacturer test reports against SEFA 8 or EN 13150 rather than relying on brochure claims.